what you need to remove starter on 2004 toyota corolla
Does your Corolla just click when you lot turn the key? If the battery and connections are okay, you may have a bad starter. Read this article for instructions on replacing the starter in a Toyota Corolla.
Note: PracticalMechanic.com is reader-supported. When you purchase through links on our site, we may earn an affiliate commission – at no cost to you. Thank you lot for your support!
Diagnosing a Bad Starter
The 2004 Toyota Corolla had been sitting outside for a couple weeks without existence started, and when I went to beginning it, and the engine wouldn't turn over. I accept heard it recommended that tapping the starter or solenoid with a hammer may jog the solenoid loose, but this trick didn't piece of work for me.
Some other thing to check is the grounding cable on the starter. Make sure it is non corroded, loose, or damaged. If it is, replace it, or get another ground going to that spot.
Starters don't like to sit idle for long periods of time. I popped the clutch and got it going. Drove it home and replaced it with a new starter at home. The process for replacing the starter is really straightforward. I would requite this job 3 out of 5 wrenches on the difficulty scale…
Tools and parts needed for this repair:
- car jack and jackstands
- Socket Wrench with 10mm and 14mm Sockets, or
- Wrench – 10mm and 12mm
- Flat-head Screwdriver
- replacement starter (Corolla)
Pace by Step Procedure for Replacing the Starter in a Toyota Corolla
These are the steps that will be covered in this picture guide:
- Remove the negative battery terminal.
- Jack upward the vehicle and secure information technology with jack-stands.
- Disconnect the plastic electric connector from the existing starter.
- Remove the grounding cablevision using a 12mm wrench.
- Remove the two 14mm bolts holding on the old starter and remove it.
- Position the new starter and re-install the two 14mm bolts.
- Reconnect the grounding cable using a 12mm wrench.
- Reconnect the electrical connector.
- Reconnect the negative battery concluding.
Detailed Procedure for Starter Replacement
The following steps walk you through the process of replacing the starter on a 2004 Toyota Corolla. These instructions would also utilise for a 2003-2008 Corolla, Matrix or Pontiac Vibe.
Disconnect the negative battery terminal using the 10mm wrench or socket.
Jack the vehicle upwards and secure it with jack-stands.
Get under the car and locate the starter.
Where is the starter located on a Toyota Corolla?
The starter on a Toyota Corolla is found right higher up the oil filter. As is seen in this photograph. The oil filter is in the lower left function of the photo, dusty orange/black and out of focus. The starter with solenoid attached is most the center of the epitome.
And so disconnect the electrical connections on the solenoid. One is a plastic connector where you lot demand to press down the tab on the side with your pollex or a flat-head screwdriver, and pull it out.
The other is the ground cable nut, remove it with a 12mm wrench.
And so remove the two 14mm bolts holding the starter on, one on the top, and one on the bottom. You may want to utilise a socket extension (3″) to get to the top commodities.
Remove the old starter. If it doesn't come loose right abroad, requite information technology a few whacks with a rubber mallet. Here's the old starter after it was removed.
Position of the new starter in the same place every bit the one-time starter. Re-insert the bolts in the reverse order.
After installing the new starter, reconnect connect the negative battery concluding.
I'yard telling y'all, this is a super easy job to do yourself. Do yourself a favor, save a couple hundred bucks and practise the repair yourself.
If y'all desire the Denso remanufactured starter, y'all can buy it here:
Denso remanufactured starter
But I bought this TYC starter off Amazon (Update: nonetheless working 4 years later on!). Here'south the link:
Corolla Starter (TYC)
Good luck!
Check out this post for tips on figuring out if the problem is your battery, starter, or alternator.
Tools and parts needed for this repair:
- motorcar jack and jackstands
- Socket Wrench with 10mm and 14mm Sockets
- Wrench – 10mm and 12mm
- Flat-head Screwdriver
- replacement starter (Corolla)
Source: https://practicalmechanic.com/2017/10/07/2004-toyota-corolla-wont-turn-over-replace-starter/
Post a Comment for "what you need to remove starter on 2004 toyota corolla"